BIT profile bending machine

SECTION BENDING TEES


Tee is made from taking a standard length of wide flange material and cutting the web to result in 2 lengths of tee material.

Tee bending machine-Profile bending machine for bending Tee profile

T Sectional Steel (or tee beams)

T beams can withstand large loads. They get their shape (and name) from the fact that they do not have a bottom flange.

T section steel is also sometimes referred to as just a ‘flange beam’ or a ‘web and flange’ or even a ‘flange and web’ beam. All these names highlight the fact that it is “missing” a second flange, which is typical of I beams.

Tees Bending
Bent tee

Tee is made from taking a standard length of wide flange material and cutting the web to result in 2 lengths of tee material.

Section bending machine can bend all types of Tee including aluminumstainless and carbon steel.

Application of T Sectional

Steel t-sections are often used in steel roof trusses to form built-up sections. The lack of a bottom flange is cost-effective in terms of needing fewer materials, but there is a trade-off. T beams are not as strong as their I-beam equivalents.

How to section bending tee profiles

Bending tee using section bending machine is very similar to bending angle profiles

Bent tee can be used for many different applications. The most common application would be as tunnel supports (shoring) or roof trusses used in steel construction.

Profile bending machine can ability to bend Tee, but you also have the ability to split beam into tee sections. When using profile bending machine to bend tee you do not have to find a secondary vendor to split the beam into tee prior to bending.

Bending Profiles Tees
Bending Profiles Tees

Section bending machine ability to bend tee sections from the very small sizes. It can bend the material with the tee stem in, stem out and stem down.

The most common bending method for bending tee material is a roll bend or pyramid bends method. Straight material is inserted into the rolls; the rolls are then moved horizontally to put the desired radius into the material. Rolling of tee material is actually very similar to rolling angle.

Just like wide flange carbon tee is classified as ASTM A992 resulting in a yield point (psi) of 50,000 minimum.

Angles are often used in tank stiffeners, matching flanges, curved lintels, hand rails, lagging rings, form work and fabricated roof trusses.

Selection table of BIT section bending machine for bending tee profiles

 Specification (mm)Minimum Inside Diameter (mm)
W24S-1680x80x9Φ700
W24S-4580x80x10Φ800
W24S-75100x100x10Φ1000
W24S-140130x130x15Φ1500
W24S-180150x150x20Φ2000
W24S-250180x180x20Φ3000
W24S-320200x200x20Φ3000
W24S-400250x250x30Φ4000
W24S-500300x300x30Φ4000
W24S-600350x350x35Φ5000

Section bending methods of metal profiles.

Select the items you want to follow based on the subtitles below.
Next, you will find relevant information, including the processing capabilities of different profile bending machines manufactured by BIT related to the project you care about.

WHAT IS PROFILE BENDING MACHINE

w24s profile bending machine

W24 SERIES SECTION BENDING MACHINE

aluminum profile bending machine

B CNC SERIES ALUMINUM PROFILE BENDING MACHINE

section bender

MS SERIES SECTION BENDER

Tolerancce Of Tee Splitting:

Quality Of Finish

Depending on the size, tees are either split using a shearing process or a flame cutting process.

Shared Tees:

‘Sheared edge’ smiliar to sheared plate. Additional grinding may be necessary depending on application. Some loss of width in addition to the normal beam manufacturers tolerance.

Flame / Plasma cut tees:

Usually 2/3 mm loss of width per cut. Tees are supplied as cut. When reversing the tees to produce tapered tees the loss of width is compunded and some remedial welding may be necessary to achieve your exact width.

Straightness of tees:

Tees are straightened to BS 4/N.S.S.S tolerances. Finer tolerances can be achieved at cost.

Length tolerance:

Plate Cutting tolerances are +/- 3mm

bent tee profiles